Emergency Battery Maintenance
The Emergency Gyro and Emergency Lighting Batteries are an important part of your Westwind’s operating systems. Chapter 5-25-00 of the 1124/1124A Westwind Maintenance Manual requires the batteries to be checked every 200 hours or 3 months. Many people consider this requirement to be a nuisance. Quite often we find the batteries have been run down or their inspection interval was ignored. Do not let this happen to you. Take the time to check your batteries. Try putting them in sync with your “A” Inspection, if possible. If you are tracking them by calendar time, be sure to give yourself enough turn time, as they require 16 hours to charge. Considering their importance in the event you should need them, you will be glad you took the time to ensure their airworthiness.
Friday, June 30, 2006
ATA 32
Brake Fuse
A fuse is installed between the forward and rear brake line at the main gear. Why is the fuse in the system? If this fuse were installed backwards, what would be the effect on the normal braking system? On the emergency braking system? Answer: The fuse is in the system to prevent the loss of braking should a rear brake line fracture. If a forward line were to fail, the emergency brake system would still function through the brake shuttle valve. If the aft line were to fail, the fuse would stop the flow of fluid overboard and allow the forward brake housing to continue to work. If the fuse were to be installed backwards, the system would work normally unless you had a rear line failure. If the rear line broke, all braking fluid to that gear would be lost overboard.
A fuse is installed between the forward and rear brake line at the main gear. Why is the fuse in the system? If this fuse were installed backwards, what would be the effect on the normal braking system? On the emergency braking system? Answer: The fuse is in the system to prevent the loss of braking should a rear brake line fracture. If a forward line were to fail, the emergency brake system would still function through the brake shuttle valve. If the aft line were to fail, the fuse would stop the flow of fluid overboard and allow the forward brake housing to continue to work. If the fuse were to be installed backwards, the system would work normally unless you had a rear line failure. If the rear line broke, all braking fluid to that gear would be lost overboard.
Labels:
ATA Chapter 32,
brake,
Fuse
ATA 21
In Flight Pressurization Issues:
An operator reported the cabin altitude would climb when the power lever was reduced during routine descents. The aircraft power lever was set to a higher setting and pressurization control was regained, followed by an uneventful landing. Note: The cabin pressure 10,000-foot red warning light did not illuminate.
During the troubleshooting process, it was noted that the left Bleed Switching Valve (BSV) was inoperative and the right High Pressure (HP) side of the right BSV was inoperative. The operator was concerned that they experienced a simultaneous failure of both valves in flight. Past experience has shown that the aircraft most likely did not have a simultaneous failure, but rather the left BSV valve had previously failed and the right BSV valve was the valve that experienced the most recent failure. The ground bypass valve is installed in the right engine bleed system, and due to the increased air flow, it is the most common selection used on the ground. Airplane Flight Manual Section IV, Normal Procedures, Before Take-Off checklist says to set the cabin air selector to both engines; however, it does not require the left bleed source be operationally checked. The aircraft will operate normally on one engine bleed source. If the left and right bleed sources are not both periodically checked, it can lead to pressurization issues in flight. It is recommended that the left bleed source be checked before takeoff to help prevent in-flight pressurization issues. It should also be noted that this condition has been seen only on the Westwind and Astra/Astra SP aircraft.
An operator reported the cabin altitude would climb when the power lever was reduced during routine descents. The aircraft power lever was set to a higher setting and pressurization control was regained, followed by an uneventful landing. Note: The cabin pressure 10,000-foot red warning light did not illuminate.
During the troubleshooting process, it was noted that the left Bleed Switching Valve (BSV) was inoperative and the right High Pressure (HP) side of the right BSV was inoperative. The operator was concerned that they experienced a simultaneous failure of both valves in flight. Past experience has shown that the aircraft most likely did not have a simultaneous failure, but rather the left BSV valve had previously failed and the right BSV valve was the valve that experienced the most recent failure. The ground bypass valve is installed in the right engine bleed system, and due to the increased air flow, it is the most common selection used on the ground. Airplane Flight Manual Section IV, Normal Procedures, Before Take-Off checklist says to set the cabin air selector to both engines; however, it does not require the left bleed source be operationally checked. The aircraft will operate normally on one engine bleed source. If the left and right bleed sources are not both periodically checked, it can lead to pressurization issues in flight. It is recommended that the left bleed source be checked before takeoff to help prevent in-flight pressurization issues. It should also be noted that this condition has been seen only on the Westwind and Astra/Astra SP aircraft.
Labels:
ATA Chapter 21,
Bleed,
BSV,
Oil pressure
Subscribe to:
Posts (Atom)
